Browse all practice questions for the NEIEP Generator Maintenance and Repair (440) Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

NEIEP Generator Maintenance and Repair (440) Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • Liquid solvent can carry particles deep into hidden recesses of a DC generator or motor. This is especially true of the spaces around which risers?
  • What is the significance of a proper stator-to-ground insulation test?
  • In lockout/tagout, the hasp is used to ______ multiple personal locks.
  • Before energizing after maintenance, guards should be ______.
  • Which protection scheme trips a generator if there is a loss of excitation?
  • In leveling, which condition can warp and raise commutator bars?
  • Using a brush grade unsuitable for the machine and duty can lead to which wear pattern?
  • Too ______ pressure causes poor brush contact and unnecessary sparking, and too _____ pressure will cause excessive brush wear.
  • During light load maintenance, which action could help reduce commutator threading?
  • ___ _____ is a short circuit that bridges one live conductor to another or to ground.
  • Compounding in generator control refers to adjusting the interaction between which parts?
  • During elevator motion, peak current should not exceed how many times the nameplate rating at full load?
  • Which bearing type is required for angular loads that may cause misalignment?
  • What is the purpose of a ground fault protector in generator systems?
  • What diagnostic test assesses insulation quality by measuring capacitance and dissipation factor?
  • What is the purpose of oil sampling and analysis in generator maintenance?
  • During peak current tests, which condition indicates a problem with control circuitry?
  • What does a "brown-out" or reduced voltage indicate in a generator under load?
  • What is the purpose of the synchronizing check and which instruments are used?
  • When brush spring pressure is too what, the brushes can arc excessively due to the poor electrical contact?
  • Which statement describes sleeve bearings relative to ball/roller bearings in terms of friction?
  • Such conditions cause what issue on commutator bars, leading to fractured brushes?
  • How does a brushless excitation system supply DC to the main field without brushes?
  • Which issue results from such bar conditions and leads to fractured brushes?
  • How can thermography assist in generator maintenance?
  • The _________ ___ must include the name or names of persons who have secured their locks to the hasp, their contact information, and the date and time when the lockout took place.
  • What is the recommended practice when performing insulation resistance tests on energized equipment?
  • Petroleum-based solvents pose which hazards that caused many elevator companies to stop using them?
  • Protective enclosures around a generator primarily ensure which safety aspects?
  • Which condition leads to excessive brush wear?
  • Which component's rattling serves as a telltale sign that sleeve bearing needs lubrication?
  • What is the recommended action if you suspect a coolant leak in the cooling system?
  • Many elevator companies no longer use which type of solvents because of health risks and fire hazards?
  • What is a standard method to verify mechanical alignment during installation and maintenance?
  • Which two tasks are among a service mechanic's most important jobs?
  • If the commutator assembly loosens, what pushes the mica outward?
  • Which material property describes carbon brushes?
  • When working with ________/___________, it is essential to replace all covers or guards before energizing the equipment.
  • For angular loads, special bearings known as ____-________ bearings are required.
  • What is the primary objective of a preventive maintenance program for generators?
  • Never heat a bearing above ___°C or ___°F.
  • Sleeve bearings require _________ inspection for signs of wear.
  • A worker who is in or may be in proximity to the work area is considered an __________ employee.
  • Which three mounting angles are considered for brush alignment?
  • If insulation resistance trends downward over time in a generator, what is the recommended action?
  • Which description best summarizes compounding adjustments?
  • Why is documenting maintenance activities and test results important?
  • In rotating machines, what type of bearings are most commonly used?
  • In winding insulation analysis, which sign indicates overheating may have occurred?
  • A key action to ensure safety during lockout/tagout is testing and verifying the circuit to ensure it is actually ______.
  • Which scenario would most justify increasing the frequency of oil analysis?
  • Which observation during testing best signals a phase-to-phase short in a three-phase stator?
  • What is the maximum temperature to heat a bearing?
  • An excess of grease can cause a ball or roller bearing to _________.
  • If a resistance measurement in a generator terminal box shows a high reading, what is this most likely to indicate?
  • Brush spacing (also called __________) can be checked by wrapping a long strip of paper around the commutator under the brushes
  • If you must adjust generator __________, always work with the series field.
  • What is the role of a governor in generator operation?
  • Most rotating machines are equipped with ____ ________.
  • Which protection is most directly associated with detecting and interrupting backward power flow from the grid into the generator, indicating islanding?
  • Which of the following is listed as a possible cause of high mica besides Normal Wear / Loosening?
  • The surface of the commutator is ______.
  • Misaligned couplings primarily cause which of the following issues?
  • One burnt segment is caused by which interpole strength condition?
  • Before paralleling a generator to a bus, what three conditions must be matched?
  • A tight fit on the shaft and in the housing will prevent this from happening.
  • How is voltage regulation stability tested under load?
  • The bearing on which end of a DC hoist motor cannot be inspected without removing it from the bedplate?
  • After inserting a new brush, how should the end of the brush be seated to the commutator?
  • Which diagnostic method helps identify bearing faults by analyzing frequency content?
  • The __________ must identify the hazards, determine the safest work practices, and provide the PPE that workers must use to protect themselves from potential flash hazards.
  • If a shielded bearing is over-lubricated or excessive pressure, the shield can be pushed against the balls. This is called a ______ shield, and the bearing will soon fail.
  • How do you verify proper phase rotation when wiring a generator to a bus?
  • Compared to ball and roller bearings, sleeve bearings have a higher coefficient of friction.
  • What is the primary function of the Automatic Voltage Regulator (AVR) in a synchronous generator?
  • Brush pressure that is too what is the single most common cause of commutator problems?
  • What does differential protection monitor in a generator?
  • Besides Normal Wear / Loosening, which is listed as a possible cause of high mica?
  • When performing generator compounding or field adjustments, which practice is recommended?
  • When performing voltage regulation stability tests on a generator under load, what is commonly used to apply the test load?
  • What term describes a commutator that has become out of round due to excessive heat?
  • Testing and verification of de-energization is performed to ensure there is no dangerous energy remaining before beginning work.
  • What could cause voltage fluctuations after synchronization that stabilize slowly?
  • How can aging insulation between turns be detected?
  • Which issues can result from misaligned couplings in a generator set?
  • When brush pressure is too what, mechanical wear is the result and higher brush temperatures can promote wear?
  • What is the purpose of protective barriers or enclosures around a generator?
  • LOTO in generator safety stands for what?
  • What is the standard symbol for protective earth grounding and where is it used?
  • Which measurement confirms that the generator is producing the correct frequency for grid synchronization?
  • In elevator speed regulation, what adjustment modifies the response time of acceleration or slowdown?
  • Arc flash temperatures can reach as high as about ______ degrees Fahrenheit.
  • Some older DC units still operate with which type of bearing?
  • The personal lock of affected employees must be secured to the ______.
  • How is reverse power protection typically applied in a generator system?
  • Brush spacing method quartering is used to check what?
  • What is a common cause of overvoltage in a generator?
  • Carbon brushes are ______.
  • Which symptom most strongly indicates a loose or failing bearing in a generator?
  • Conductive emery particles lodged between commutator bars can cause which electrical fault?
  • When performing winding resistance checks, what is a typical trend to expect with healthy windings?
  • Which condition can cause brushes to stick in their holder?
  • What is the correct gap range for MG sets and DC hoist motors?
  • A significant deviation in winding resistance between phases indicates which issue?
  • After starting a generator, what is a key operating check before applying load?
  • Which are typical indicators that cooling system maintenance is due?
  • When performing compounding adjustments on a generator, you should work with which field?
  • The continual friction of the brushes against the _________ _____________ wears the brushes down and tends to force them out of alignment, which causes trouble in commutation.
  • Which tool is used to drive a bearing onto a shaft without damaging the inner race?
  • How would you identify a loose connection in a generator terminal box?
  • Liquid solvent ________ ___ be applied to a commutator.
  • What describes isochronous governor control in parallel operation?
  • In vibration analysis, which finding indicates a bearing fault such as a ball bearing fault?
  • Which type of bearing is preferred on rotating machines because of their very low coefficient of friction and maintenance?
  • How can you detect a phase-to-phase short in a three-phase stator during testing?
  • In parallel operation, if the phase angle is not matched, what issue can occur?
  • What are the two standard tests used to determine a synchronous generator’s impedance characteristics?
  • For proper commutation and brush life, the mica insulation between commutator bars should be _____ ___ _______.
  • What term describes the period of adjustment required before brushes operate at their best?
  • A radial load applies a force at __° to the centerline of the shaft.
  • Why is oil cleanliness critical for generator bearings?
  • Dust and dirt cause bearing wear primarily through which mechanism?
  • Which condition most commonly causes streaking on a commutator?
  • Which of the following is a precise method to verify shaft alignment?
  • Insufficient brush spring pressure causes what at the carbon-to-copper junction?
  • Arc flash can reach temperatures exceeding which approximate value in degrees Fahrenheit?
  • What does a compounding adjustment involve to regulate voltage under varying loads?
  • The ___________ must be mechanically true, the unit in good balance, and the ________ in good shape and properly adjusted
  • Brushes require a running-in period before they operate at their best. What is the term for this period?
  • Ball bearings may be open, shielded, or sealed.
  • Grooving on a commutator is caused by which factor?
  • A sleeve bearing wears quietly and allows the armature to _____, reducing clearances.
  • What practice supports traceability and regulatory compliance in generator maintenance?
  • The relief plug _______ be removed from the bearing housing.
  • What is the main purpose of maintaining proper generator cooling?
  • Use a ______-____ _______ ______when force is required to drive it on a shaft. The ______-____ _______ ______ puts the driving force against the inner race, where it cannot do damage.
  • Lockout procedures commonly lock the energy isolating device using which component?
  • In insulation testing, tan delta is a measure of what?
  • What polarization index is used for in insulation testing?
  • What does the short-circuit test reveal about a generator?
  • Sometimes a ________ adjustment to acceleration or slowdown will help.
  • Bearing wear is indicated by which symptom?
  • Whenever possible, it is best to ______ or ______ out these hazards.
  • Insufficient brush spring pressure creates an increase in what at the carbon-to-copper junction?
  • ________ losses are present in all rotating machines. Even brushes riding on the commutator are a source of ________.
  • What is the primary protective purpose of PPE in maintenance work?
  • What is the purpose of oil analysis in generator maintenance?
  • What tool is commonly used to assess insulation condition between windings and ground?
  • Why is it important to verify phase rotation before closing the breaker on a generator connected to a bus?
  • If peak current is higher than the specified multiple, what should you check?
  • Conductive particles washed into these spaces will eventually ______ ___, requiring removal of the armature for repairs.
  • What is the role of a maintenance preventive plan for generators?
  • Light electrical load causes commutator ______.
  • If conductive particles short the areas around the commutator risers, what maintenance action is typically required?
  • In a DC machine, which components are typically the source of mechanical friction?
  • The mica insulation between commutator bars should be kept below the surface. This statement describes what relationship?
  • Why should shaft alignment be verified at operating temperature and load?
  • Which finding on commutator bars can cause brush chatter?
  • A ball bearing designed to carry radial loads, such as in a motor or MG set, will not last long if subjected to ________ loads.
  • What happens to the armature clearance as the sleeve bearing wears?
  • A condition called ________ __________ develops on the outer surface of the inner and/or outer bearing race. A tight fit on the shaft and in the housing will prevent this from happening.
  • During synchronization, which instrument is commonly used to visually compare the rotor position with the bus voltage to decide when to close the breaker?
  • There is no way to add lubricant to a _______ bearing.
  • If peak current remains elevated after adjustments, what should be checked?
  • The lockout tag should include which information?
  • Usually, the only friction present in a DC machine is from the _________ and ________.
  • If the commutator is not mechanically true, what issue is most likely?
  • Bar Edge Burning is a fault in a commutator. Which of the following describes a related condition?
  • Bearing oil is described as having which viscosity?
  • What should be used as a last line of defense?
  • The most common causes of _________ _______ include improper seating, bearing misalignment, poor installation, vibration due to imbalance, and passage of electric current through the bearing.
  • What is the primary cause of bearing wear and failure?
  • Excessive heat can cause a commutator to become what, or out of round?
  • The other source of friction is the bearings supporting the _________ _____.
  • What is a common indication of winding overheating in a generator’s insulation system?
  • What is the effect of a shorted turn in a stator winding?
  • Why is moisture control important in a generator enclosure, and what is a common method to manage it?
  • Which maintenance technology is most effective for detecting winding hot spots before insulation damage occurs?
  • The trueness of a commutator is held to about what tolerance?
  • There are three types of mounting angles to consider: ______, _______ , and _________.
  • On MG sets and DC hoist motors, the correct gap is approximately ____ to ____ inches.
  • Why is bearing lubrication and oil level monitoring included in routine generator maintenance?
  • Which parameter does the short-circuit test determine?
  • Which of the following is a common method to manage moisture in a generator enclosure?
  • How should you perform a safe starter/stop sequence for a generator?
  • What does the open-circuit (no-load) test primarily determine?
  • Which describes a shielded bearing when over-lubrication leads to failure?
  • Which component's rattling serves as a telltale sign that the sleeve bearing needs oil?
  • What does the open-circuit (no-load) test reveal about a generator?
  • What is an essential safety practice before performing generator maintenance?
  • Under heavy operating temperatures, how does commutator trueness change?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy